Pass4itsure accurate MCSA Windows Server 70-740 dumps pdf exams download for installation, storage, and compute with the knowledge and skills. Pass4itsure is website that can help a lot of IT people realize their dreams. If you have a IT dream then quickly click the Microsoft https://www.pass4itsure.com/70-740.html dumps.
Exam Code: 70-740
Exam Name: Installation, Storage, and Compute with Windows Server 2016
Updated: Aug 27, 2017
Q&As: 162
[New Microsoft 70-740 Dumps Updated August From Google Drive]: https://drive.google.com/open?id=0BwxjZr-ZDwwWVTIxOHJfTzhJNDg
[New Cisco 300-075 Dumps Updated August From Google Drive]: https://drive.google.com/open?id=0BwxjZr-ZDwwWTk00ekx3V0xfX3c
Pass4itusre Latest and Most Accurate Microsoft 70-698 Dumps Exam Q&As:
QUESTION 1
What type of analysis would NOT normally be completed when optimising PS data
services?
A. Evaluating traffic volume thresholds.
B. Evaluating UE transmit power thresholds.
C. Evaluating downlink transmit power thresholds.
D. Evaluating the delay for the CELLFACH to CELLDCH transition.
70-740 exam Answer: B
QUESTION 2
Which RLC mode should be used for NRT traffic?
A. AM.
B. UM.
C. TrM.
D. FM.
Answer: A
QUESTION 3
How is the SHO area optimised?
A. By adding neighbours for Inter-system handovers.
B. By fine-tuning the HC and PC control parameters.
C. By increasing the TX Power and LNA gain.
D. By adjusting cell dominance areas.
70-740 dumps Answer: D
QUESTION 4
What is the CORRECT order of the major phases in the ISHO process?
A. Compressed mode, event or periodical measurement reporting, threshold comparison.
B. Event or periodical measurement reporting, compressed mode, threshold comparison.
C. Initial triggering, compressed mode, event measurement reporting, threshold
comparison.
D. Initial triggering, compressed mode, periodical measurement reporting, threshold
comparison.
Answer: D
QUESTION 5
The Dedicated Traffic Channel (DTCH):
A. is a point to multipoint channel.
B. exists only in uplink.
C. exists only in downlink.
D. is used to transfer user information.
70-740 pdf Answer: D
QUESTION 6
The GSM – WCDMA handover process for voice, from measurements triggering to
complete handover, takes:
A. 7-10 seconds.
B. 0.02-0.04 of a second.
C. 2-5 seconds.
D. 0.2-0.4 of a second.
Answer: C
QUESTION 7
When applying the free space propagation loss formula both for GSM900 and WCDMA,
what APPROXIMATELY is the propagation loss difference between the systems, if the
distance from the BTS is 1500 meters? (Use frequency 2100 MHz for WCDMA.)
A. 5.5 dB.
B. 7.4 dB.
C. 1.3 dB.
D. 13.4 dB.
70-740 vce Answer: B
QUESTION 8
Pilot pollution can be observed from:
A. nodeB TX and RX statistics from OSS.
B. field measurements.
C. nodeB statistics from Iub.
D. RNC handover statistics.
Answer: B
QUESTION 9
What is the CORRECT coding sequence in a DL transmission?
A. First channalisation then scrambling.
B. First scrambling then rate matching.
C. First scrambling then channalisation.
D. First scrambling then convolutional.
70-740 exam Answer: A
QUESTION 10
Which one of the following parameters does NOT have an influence on UL traffic
capacity?
A. RACH process.
B. Power control algorithm.
C. Active set size.
D. S-criteria.
Answer: D
QUESTION 11
What happens in the UE when compressed mode is in operation?
A. Transmission and reception are halted for a short time in order to perform
measurements on the other frequencies.
B. Transmission is halted for a short time in order to perform measurements on the other
frequencies.
C. Transmission and reception continue normally while the UE measures the other
frequencies.
D. Reception is halted for a short time in order to perform measurements on the other
frequencies.
70-740 dumps Answer: A
QUESTION 12
What is “little i”?
A. The interference ratio from neighbouring cells to own cell.
B. The inter-working between 2G and 3G system.
C. The interference margin of own cell.
D. The inter-system handover margin.
Answer: A
QUESTION 13
Which one of the following statements is CORRECT when the CPICH pilot power is too
low in one cell?
A. CPICH pilot power has no effect on Soft handovers.
B. Soft handovers are delayed.
C. Soft handovers are happening earlier.
D. Soft handovers are not working.
70-740 pdf Answer: C
QUESTION 14
For what purpose are the raw counters usually used?
A. To monitor system level performance
B. To monitor end user performance
C. To record the throughput
D. To troubleshoot cell specific issues
Answer: D
QUESTION 15
For the CELLFACH state, which one of the following statements is NOT true?
A. The UE is enabled to transmit uplink control messages and may also be able to
transmit small data packets on the RACH.
B. Listens to the PCH transport channel (via allocated PICH) for the decoding of paging
and notification messages sent by the RAN.
C. A cell update procedure is used to report to the RNC, when the UE executes cell
re-selection.
D. The location of the UE is known on cell level in RNC.
70-740 vce Answer: B
QUESTION 16
The RadioBearerSetup message:
A. is sent in uplink.
B. is sent in downlink.
C. can replace the RRCConnectionSetup to speed up the call set-up.
D. is the downlink answer to the RadioBearerRequest.
Answer: B
QUESTION 17
If the coverage area of the site with 12.2 kbps voice services and 141.9 dB path loss is
17.5 km2, what is the cell radius assuming that the site has 3 sectors (k factor for site area
is 2.2)?
A. 2.2 km.
B. 2.8 km.
C. 3.3 k
D. 1.6 km.
70-740 exam Answer: B
QUESTION 18
For the use of a shared antenna line between GSM and WCDMA, what is needed?
A. Diplexer or triplexer.
B. Same output power both GSM and WCDMA.
C. Coupler or splitter.
D. One shared BTS for GSM and WCDMA.
Answer: A
QUESTION 19
Which one of the following channels does NOT have an influence on DL coverage?
A. PRACH.
B. BCCH.
C. PCH.
D. SCH.
70-740 dumps Answer: A
QUESTION 20
In the call-setup phase, on which transport channel is the RRCConnectionSetup
message sent?
A. BCH.
B. RACH.
C. CCCH.
D. FACH.
Answer: D
QUESTION 21
Which one of the following is the CORRECT range for Routing Area?
A. 0 – 63.
B. 0 – 127.
C. 0 -15.
D.0 – 255.
70-740 pdf Answer: D
QUESTION 22
In a cell reselection, UE neighbour measurements can be seen:
A. always at the same time for all cells.
B. always at different time for all cells.
C. only for three best cells at the same time.
D. depending on parameter settings of measurements of different cell types.
Answer: D
QUESTION 23
Considering 1 site (3 cells) with 1 only one carrier per cell, how many traffic hardware
channels are needed if in the site the active users are: 1.8 voice, 0.7 CS64, 0.7 PS64 and 1
PS384 and knowing that for each connection the following hardware channels apply: 1
for voice, 4 for CS64, 4 for PS64 and 16 for PS384 are needed?
A. 24
B. 4
C. 37
D. 13
70-740 vce Answer: A
QUESTION 24
For proper cell (re)selection UE needs which one of the following parameter settings?
A. Spreading codes.
B. Location area identifications.
C. Scrambling codes.
D. CPICH TX levels.
Answer: C
QUESTION 25
Inter-system handover parameter settings at the 3G-coverage border should be evaluated
at a level of:
A. cell and RNC.
B. site and RNC.
C. cell and site.
D. site and MSC.
70-740 exam Answer: A
QUESTION 26
Which one of the following statements regarding physical channel and power control
pairs is NOT true?
A. S-CCPCH has inner loop power control.
B. PRACH uses open loop power control.
C. FACH and PCH do not have inner loop power control.
D. DCH utilizes fast power control.
Answer: A
It has the best MCSA Windows Server 2016 70-740 dumps questions, which is Pass4itsure MCSA Windows Server 2016 70-740 questions. This MCSA Windows Server 2016 70-740 exam questions is what IT people are very wanted. Because it will make you pass the https://www.pass4itsure.com/70-740.html dumps exam easily, since then rise higher and higher on your career path.
Package Includes:http://www.exampass.net/cisco-300-170-dumps.html
Note that www.cisco.com is a great place to start: http://www.certificationpdf.com/most-popular-cisco-ciptv1-300-070-dumps-exam/